1 (06.04.2011 23:59 отредактировано skp@Linux)

Тема: Настройка TouchPad в Debian

Настройка TouchPad в Debian

Следующая команда, позволяет узнать, имеете ли вы touchpad и загружен ли его драйвер:

egrep -i 'synap|alps|etps' /proc/bus/input/devices
Мой вывод:

Name="SynPS/2 Synaptics TouchPad"

Поздравляю сам себя, я имею touchpad, хотя я его и так вижу невооруженным взглядом.
Редактируем  /etc/X11/xorg.conf


Section "Module"
    Load "synaptics"
EndSection

......

Section "InputDevice"
  Identifier      "Synaptics Touchpad"
  Driver          "synaptics"
#  Option          "SendCoreEvents"        "true"
  Option          "Device"                "/dev/psaux"
  Option          "Protocol"              "auto-dev"
  Option          "HorizEdgeScroll"       "0"
  Option          "SHMConfig"             "true"
  Option          "Emulate3Buttons"   "on"
  Option          "LeftEdge"      "1700"
  Option          "RightEdge"     "5300"
  Option          "TopEdge"       "1700"
  Option          "BottomEdge"    "4200"
  Option          "FingerLow"     "35"
  Option          "FingerHigh"    "40"
  Option          "MaxTapTime"    "180"
  Option          "MaxTapMove"    "220"
  Option          "VertScrollDelta" "100"
  Option          "MinSpeed"      "0.06"
  Option          "MaxSpeed"      "0.12"
  Option          "AccelFactor" "0.0010"
  Option          "TapButton1" "1" #именно эта опция отвечает за работу клика по тачпаду
EndSection
....

Section "ServerLayout"
    InputDevice "Synaptics Touchpad" "SendCoreEvents"
EndSection

....

Радуемся, недолго. Печатать неудобно, постоянно за него задеваешь, необходима прога/проги для его настройки. И такая проги есть, называются synclient и syndaemon. В принципе этого достаточно.

Тонкая настройка при помощи synclient

Чтобы получить текущие значения:

  $ synclient -l

Таким образом, вы получите список всех действующих на данный момент значений.

Монитор synclient может отображать силу нажатия и положение пальца на тачпаде в реальном времени, позволяя точно задавать опции synaptics под свои нужды. Для работы synclient требуется чтобы опция SHMConfig была установлена в on или true.
Вы можете запустить монитор synaptics следующей командой:

$ synclient -m 100

где -m активирует монитор, а следующее за опцией число задаёт интервал обновления в миллисекундах.
Этот монитор предоставляет информацию о текущем состоянии вашего тачпада. Например, если вы двигаете тачпадом указатель мыши, то значения x и y в мониторе synclient будут изменяться. Таким образом вы можете легко узнать виртуальные размеры вашего тачпада, которые задаються в опциях LeftEdge, RightEdge, BottomEdge и TopEdge.

Аббревиатуры расшифровываются следующим образом:

time

время в секундах с начала логирования.
x, y

координаты x/y пальца на тачпаде. Точка отсчёта — верхний левый угол.
z

давление. Характеризует вашу силу нажатия на тачпад при работе с ним.
f

количество пальцев, которые сейчас прикасаются к тачпаду.
w

ширина пальца.
l,r,u,d,m,multi

состояния левой(left), правой(right), (верхней)up, (нижней)down, (средней)middle и многофункциональной (multi) кнопок. Нажатое состояние отражается единицей, ненажатое — нулём.
gl,gm,gr

для тачпадов с подключаемым устройством (guest device) эти параметры соответствуют его состоянию кнопок: левой(guest left), средней(guest middle) и правой (guest right). Кнопки могут быть нажаты(1) или не нажаты(0).
gdx, gdy

координаты x/y подключаемого устройства (guest device).
Если какое-то значение постоянно равно нулю, это означает что ваше устройство не поддерживает его.

Если графа f отображает максимальное значение 1, но есть необходимость в использовании двухпальцевого режима, в таком случае обратите внимание на опции EmulateTwoFingerMinW,EmulateTwoFingerMinZ и EmulateMidButtonTime и добавьте соответствующие строки в файл xorg.conf.

Вооружившись этими знаниями вы сможете подобрать правильные значения для вашего тачпада.

Детальная конфигурация

Драйвер synaptics предоставляет множество опций для настройки. Следующий список описывает опции секции InputDevice, которую мы объявили в конфигурационном файле Xorg:

Identifier — имя этого устройства ввода, которое мы указали в секции ServerLayout выше.

Device указывает на файл устройства synaptic.

LeftEdge, RightEdge, TopEdge и BottomEdge — целые числа, которые задают виртуальные размеры вашего тачпада в координатах x и y.

FingerLow и FingerHigh — целочисленные значения, определяющие 'силу нажатия', которую драйвер расценит как прикосновение (сила нажатия становится больше FingerHigh) или отпускание (сила нажатия падает ниже FingerLow).

MaxTapTime — целое число, определяющее максимальную задержку в миллисекундах для одиночного нажатия (tap), которое рассматривается как клик мыши.

MaxTapMove — целое число, определяющее максимальное перемещение пальца для засчитывания одиночного нажатия (tap).

MinSpeed и MaxSpeed являются минимальным и максимальным коэффициентами скорости. Дробные числа с плавающей точкой.

AccelFactor — коэффициент ускорения, также дробное число с плавающей точкой.

SHMConfig — булевское значение (on/off) для включения/выключения использования разделяемой памяти. Эта опция должна быть включена, если вы хотите наблюдать и конфигурировать ваше устройство synaptics такими клиентскими утилитами как synclient, который мы будем использовать в данной статье.

EmulateTwoFingerMinW' , EmulateTwoFingerMinZ' , EmulateMidButtonTime — опции для настройки эмуляции клика двумя пальцами.

Больше информации по опциям вы найдёте на man-страничке synaptics:

$ man 5 synaptics

Отключение кликов мыши при наборе с клавиатуры

Это маленькая хитрость встроенная в драйвер synaptics, позволяет быть уверенным, что тачпад отключен во время набора с клавиатуры. Это очень легко настроить, и здесь я опишу как это сделать.

просто добавьте следующую строку в ваш .xinitrc до запуска оконного менеджера:

syndaemon -i 2 -d
Ключ -i 2 устанавливает время простоя в 2 секунды. Это интервал, который будет проходить со времени последнего нажатия клавиши до включения тачпада обратно, а опция -d запускает программу в качастве демона ( в фоновом режиме ).

Также вы можете добавить ключ -t который говорит демону не отключать перемещение мыши, а отключать только клики и прокрутку:

syndaemon -t -i 2 -d
Как обычно более детальную информацию вы можете найти на man-страничке:

$ man syndaemon

К большому сожалению, программы ksynaptic и qsynaptic устарели и автор больше их не разрабатывает. Для Gnome есть gsynaptics.

Оригинал статьи http://deb-th.org/index.php/Touchpad_Synaptics_русский.

TouchPad и мышь

Площадка на ноуте, мешающая мне лично жить, так как пользуюсь внешней мышью.
Вот как отключить touchpad при втыкании внешней мыши.

Запускаем следующую команду:

udevadm monitor --env

и вставляем usb мышь в разъем. Получается предлинный список, вот значимый фрагмент:


UEVENT[1281016708.743148] add      /devices/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0458:003A.0027 (hid)
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0458:003A.0027
SUBSYSTEM=hid
PHYSDEVBUS=hid
HID_ID=0003:00000458:0000003A
HID_NAME=Genius Optical Mouse
HID_PHYS=usb-0000:00:04.0-2/input0
HID_UNIQ=
MODALIAS=hid:b0003v00000458p0000003A
SEQNUM=12511

ищем в выводе команды слово mouse, меня сразу интересует вот эта строчка:

DEVPATH=/devices/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0458:003A.0027

Запускаем следующую команду:

sudo udevadm info -a -p /devices/pci0000:00/0000:00:04.0/usb1/1-2/1-2:1.0/0003:0458:003A.0027 | grep product

Вот вывод:

ATTRS{product}=="Optical Mouse"
ATTRS{product}=="OHCI Host Controller"

Пишем обработчик для udev:

/etc/udev/rules.d/76-mouse.rules

ACTION=="add", SUBSYSTEMS=="usb", ATTRS{product}=="Optical Mouse", RUN+="/sbin/rmmod psmouse"
ACTION=="remove", SUBSYSTEMS=="usb", ATTRS{product}=="Optical Mouse", RUN+="/sbin/modprobe psmouse"

Посел чего touchpad будет отключаться при втыкании usb мыши и включаться при ее выдергивании.

Чтобы touchpad устройство было выключенным по умолчанию, сразу при запуске компьютера добавьте rmmod psmouse в файл /etc/rc.local.

Увы, путь загрузки/удаления модуля не позволяет регулировать свойства TouchPadа, поэтому лучше использовать вот это:

ACTION=="add", SUBSYSTEMS=="usb", ATTRS{product}=="Optical Mouse", RUN+="/usr/bin/synclient TouchpadOff=1"
ACTION=="remove", SUBSYSTEMS=="usb", ATTRS{product}=="Optical Mouse", RUN+="/usr/bin/synclient TouchpadOff=0"

Так будет более правильней.

Полезный сценарий, который надо поместить в автозагрузку Gnome или KDE:

mouse.sh

#! /bin/sh
if [ -c /dev/input/mouse0 ] && [ -c /dev/input/mouse1 ] ; then
# если есть две мыши, то одна лишняя.
/usr/bin/synclient TouchpadOff=1
fi

2 (11.01.2012 14:38 отредактировано NEVOFF)

Re: Настройка TouchPad в Debian

А я вот не могу себя поздравить, ибо у меня тачпада нету(( Хотя я тоже вижу его невооруженным глазом( Что делать??:((

3

Re: Настройка TouchPad в Debian

И к кому претензии? Мы тут все - люди Хэ, телепаты как один smile
Модель ноута давай и выхлопы lspci и dmesg.

4

Re: Настройка TouchPad в Debian

Уф, вышеописанные махинации пока сложноваты для меня... Подскажите, пожалуйста, как повесить на хоткеи включение-отключение тачпада? Ноут- asus k50c, система waldorf с последними обновлениями, lspci:

andrey@crunchbang:~$ lspci
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 671MX
00:01.0 PCI bridge: Silicon Integrated Systems [SiS] AGP Port (virtual PCI-to-PCI bridge)
00:02.0 ISA bridge: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] (rev 01)
00:02.5 IDE interface: Silicon Integrated Systems [SiS] 5513 IDE Controller (rev 01)
00:03.0 USB controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.1 USB controller: Silicon Integrated Systems [SiS] USB 1.1 Controller (rev 0f)
00:03.3 USB controller: Silicon Integrated Systems [SiS] USB 2.0 Controller
00:05.0 IDE interface: Silicon Integrated Systems [SiS] SATA Controller / IDE mode (rev 03)
00:06.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:07.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
00:0f.0 Audio device: Silicon Integrated Systems [SiS] Azalia Audio Controller
00:1f.0 PCI bridge: Silicon Integrated Systems [SiS] PCI-to-PCI bridge
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter (rev 10)
02:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)

dmesg:

andrey@crunchbang:~$ dmesg
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Initializing cgroup subsys cpu
[    0.000000] Linux version 3.2.0-4-486 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-15) ) #1 Debian 3.2.41-2
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000077fb8000 (usable)
[    0.000000]  BIOS-e820: 0000000077fb8000 - 0000000077fc0000 (ACPI NVS)
[    0.000000]  BIOS-e820: 0000000077fc0000 - 0000000077fce000 (ACPI data)
[    0.000000]  BIOS-e820: 0000000077fce000 - 0000000078000000 (ACPI NVS)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000] Notice: NX (Execute Disable) protection cannot be enabled: non-PAE kernel!
[    0.000000] SMBIOS 2.5 present.
[    0.000000] DMI: ASUSTeK Computer Inc.  K50C/K50C      , BIOS 209     01/06/2010
[    0.000000] e820 update range: 0000000000000000 - 0000000000010000 (usable) ==> (reserved)
[    0.000000] e820 remove range: 00000000000a0000 - 0000000000100000 (usable)
[    0.000000] last_pfn = 0x77fb8 max_arch_pfn = 0x100000
[    0.000000] MTRR default type: uncachable
[    0.000000] MTRR fixed ranges enabled:
[    0.000000]   00000-9FFFF write-back
[    0.000000]   A0000-BFFFF uncachable
[    0.000000]   C0000-CFFFF write-protect
[    0.000000]   D0000-EFFFF uncachable
[    0.000000]   F0000-FFFFF write-protect
[    0.000000] MTRR variable ranges enabled:
[    0.000000]   0 base 078000000 mask FF8000000 uncachable
[    0.000000]   1 base 000000000 mask F80000000 write-back
[    0.000000]   2 disabled
[    0.000000]   3 disabled
[    0.000000]   4 disabled
[    0.000000]   5 disabled
[    0.000000]   6 disabled
[    0.000000]   7 disabled
[    0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[    0.000000] found SMP MP-table at [c00ff780] ff780
[    0.000000] initial memory mapped : 0 - 01800000
[    0.000000] Base memory trampoline at [c009c000] 9c000 size 12288
[    0.000000] init_memory_mapping: 0000000000000000-00000000377fe000
[    0.000000]  0000000000 - 0000400000 page 4k
[    0.000000]  0000400000 - 0037400000 page 2M
[    0.000000]  0037400000 - 00377fe000 page 4k
[    0.000000] kernel direct mapping tables up to 377fe000 @ 17fa000-1800000
[    0.000000] RAMDISK: 36c38000 - 37614000
[    0.000000] ACPI: RSDP 000fa260 00014 (v00 _ASUS_)
[    0.000000] ACPI: RSDT 77fc0000 00050 (v01 _ASUS_ RSDT1005 20100106 MSFT 00000097)
[    0.000000] ACPI: FACP 77fc0200 00084 (v01 _ASUS_ FACP1005 20100106 MSFT 00000097)
[    0.000000] ACPI: DSDT 77fc0690 09899 (v01  K50C0 K50C0209 00000209 INTL 20051117)
[    0.000000] ACPI: FACS 77fce000 00040
[    0.000000] ACPI: APIC 77fc0390 0006C (v01 _ASUS_ APIC1005 20100106 MSFT 00000097)
[    0.000000] ACPI: MCFG 77fc0440 0003C (v01 _ASUS_ OEMMCFG  20100106 MSFT 00000097)
[    0.000000] ACPI: OEMX 77fc0480 00176 (v01 _ASUS_ OEMX1005 20100106 MSFT 00000097)
[    0.000000] ACPI: ECDT 77fc0630 00055 (v01 _ASUS_ OEMECDT  20100106 MSFT 00000097)
[    0.000000] ACPI: DBGP 77fc0400 00034 (v01 _ASUS_ DBGP1005 20100106 MSFT 00000097)
[    0.000000] ACPI: BOOT 77fc0600 00028 (v01 _ASUS_ BOOT1005 20100106 MSFT 00000097)
[    0.000000] ACPI: OEMB 77fce040 00071 (v01 _ASUS_ OEMB1005 20100106 MSFT 00000097)
[    0.000000] ACPI: HPET 77fc9f30 00038 (v01 _ASUS_ OEMHPET  20100106 MSFT 00000097)
[    0.000000] ACPI: SSDT 77fce0c0 00594 (v01  PmRef  Cpu0Cst 00003001 INTL 20051117)
[    0.000000] ACPI: SSDT 77fce660 002D7 (v01  PmRef   CpuPm1 00003000 INTL 20051117)
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] 1031MB HIGHMEM available.
[    0.000000] 887MB LOWMEM available.
[    0.000000]   mapped low ram: 0 - 377fe000
[    0.000000]   low ram: 0 - 377fe000
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA      0x00000010 -> 0x00001000
[    0.000000]   Normal   0x00001000 -> 0x000377fe
[    0.000000]   HighMem  0x000377fe -> 0x00077fb8
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[2] active PFN ranges
[    0.000000]     0: 0x00000010 -> 0x0000009f
[    0.000000]     0: 0x00000100 -> 0x00077fb8
[    0.000000] On node 0 totalpages: 491335
[    0.000000] free_area_init_node: node 0, pgdat c13c5938, node_mem_map f5d38200
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 3951 pages, LIFO batch:0
[    0.000000]   Normal zone: 1744 pages used for memmap
[    0.000000]   Normal zone: 221486 pages, LIFO batch:31
[    0.000000]   HighMem zone: 2064 pages used for memmap
[    0.000000]   HighMem zone: 262058 pages, LIFO batch:31
[    0.000000] Using APIC driver default
[    0.000000] ACPI: PM-Timer IO Port: 0x808
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 20, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] ACPI: HPET id: 0x10398201 base: 0xfed00000
[    0.000000] nr_irqs_gsi: 40
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] Allocating PCI resources starting at 78000000 (gap: 78000000:86e00000)
[    0.000000] Booting paravirtualized kernel on bare hardware
[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[    0.000000] pcpu-alloc: [0] 0 
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 487495
[    0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-486 root=UUID=3edae456-0618-4f19-873c-d19b62cbd96d ro quiet
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Initializing CPU#0
[    0.000000] Initializing HighMem for node 0 (000377fe:00077fb8)
[    0.000000] Memory: 1934144k/1965792k available (2590k kernel code, 31196k reserved, 1299k data, 452k init, 1056488k highmem)
[    0.000000] virtual kernel memory layout:
[    0.000000]     fixmap  : 0xfffa1000 - 0xfffff000   ( 376 kB)
[    0.000000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.000000]     vmalloc : 0xf7ffe000 - 0xff7fe000   ( 120 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf77fe000   ( 887 MB)
[    0.000000]       .init : 0xc13cd000 - 0xc143e000   ( 452 kB)
[    0.000000]       .data : 0xc12878ec - 0xc13cc580   (1299 kB)
[    0.000000]       .text : 0xc1000000 - 0xc12878ec   (2590 kB)
[    0.000000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.000000] NR_IRQS:2304 nr_irqs:256 16
[    0.000000] CPU 0 irqstacks, hard=f5808000 soft=f580a000
[    0.000000] Console: colour VGA+ 80x25
[    0.000000] console [tty0] enabled
[    0.000000] hpet clockevent registered
[    0.000000] Fast TSC calibration failed
[    0.000000] TSC: PIT calibration matches HPET. 1 loops
[    0.000000] Detected 1500.334 MHz processor.
[    0.008002] Calibrating delay loop (skipped), value calculated using timer frequency.. 3000.66 BogoMIPS (lpj=6001336)
[    0.008008] pid_max: default: 32768 minimum: 301
[    0.008048] Security Framework initialized
[    0.008056] AppArmor: AppArmor disabled by boot time parameter
[    0.008070] Mount-cache hash table entries: 512
[    0.008191] Initializing cgroup subsys cpuacct
[    0.008197] Initializing cgroup subsys memory
[    0.008205] Initializing cgroup subsys devices
[    0.008208] Initializing cgroup subsys freezer
[    0.008211] Initializing cgroup subsys net_cls
[    0.008214] Initializing cgroup subsys blkio
[    0.008222] Initializing cgroup subsys perf_event
[    0.008256] using mwait in idle threads.
[    0.008263] CPU: Intel(R) Celeron(R) D CPU        220  @ 1.20GHz stepping 01
[    0.008930] ACPI: Core revision 20110623
[    0.016064] Performance Events: PEBS fmt0-, Core2 events, Intel PMU driver.
[    0.016078] ... version:                2
[    0.016081] ... bit width:              40
[    0.016083] ... generic registers:      2
[    0.016085] ... value mask:             000000ffffffffff
[    0.016088] ... max period:             000000007fffffff
[    0.016090] ... fixed-purpose events:   3
[    0.016092] ... event mask:             0000000700000003
[    0.016314] NMI watchdog enabled, takes one hw-pmu counter.
[    0.016363] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.016662] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.060003] devtmpfs: initialized
[    0.060003] PM: Registering ACPI NVS region at 77fb8000 (32768 bytes)
[    0.060003] PM: Registering ACPI NVS region at 77fce000 (204800 bytes)
[    0.060003] print_constraints: dummy: 
[    0.060003] NET: Registered protocol family 16
[    0.060003] EISA bus registered
[    0.060003] ACPI: bus type pci registered
[    0.060003] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.060003] PCI: not using MMCONFIG
[    0.060003] PCI: PCI BIOS revision 3.00 entry at 0xf0031, last bus=4
[    0.060003] PCI: Using configuration type 1 for base access
[    0.060003] bio: create slab <bio-0> at 0
[    0.060003] ACPI: Added _OSI(Module Device)
[    0.060003] ACPI: Added _OSI(Processor Device)
[    0.060003] ACPI: Added _OSI(3.0 _SCP Extensions)
[    0.060003] ACPI: Added _OSI(Processor Aggregator Device)
[    0.060571] ACPI: EC: EC description table is found, configuring boot EC
[    0.062106] ACPI: Executed 1 blocks of module-level executable AML code
[    0.068589] ACPI: Interpreter enabled
[    0.068615] ACPI: (supports S0 S3 S4 S5)
[    0.068647] ACPI: Using IOAPIC for interrupt routing
[    0.069116] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[    0.069888] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[    0.069892] PCI: Using MMCONFIG for extended config space
[    0.077274] ACPI: EC: GPE = 0x19, I/O: command/status = 0x66, data = 0x62
[    0.077490] ACPI: No dock devices found.
[    0.077494] HEST: Table not found.
[    0.077503] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[    0.077781] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[    0.078066] pci_root PNP0A03:00: host bridge window [io  0x0000-0x0cf7]
[    0.078071] pci_root PNP0A03:00: host bridge window [io  0x0d00-0xffff]
[    0.078075] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[    0.078079] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
[    0.078082] pci_root PNP0A03:00: host bridge window [mem 0x78000000-0xdfffffff]
[    0.078086] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
[    0.078112] pci 0000:00:00.0: [1039:0671] type 0 class 0x000600
[    0.078127] pci 0000:00:00.0: reg 10: [mem 0xf0000000-0xf7ffffff]
[    0.078205] pci 0000:00:01.0: [1039:0003] type 1 class 0x000604
[    0.078253] pci 0000:00:02.0: [1039:0968] type 0 class 0x000601
[    0.078350] pci 0000:00:02.5: [1039:5513] type 0 class 0x000101
[    0.078410] pci 0000:00:02.5: reg 20: [io  0xfff0-0xffff]
[    0.078461] pci 0000:00:02.5: PME# supported from D3cold
[    0.078484] pci 0000:00:03.0: [1039:7001] type 0 class 0x000c03
[    0.078500] pci 0000:00:03.0: reg 10: [mem 0xfe8ff000-0xfe8fffff]
[    0.078572] pci 0000:00:03.1: [1039:7001] type 0 class 0x000c03
[    0.078588] pci 0000:00:03.1: reg 10: [mem 0xfe8fe000-0xfe8fefff]
[    0.078666] pci 0000:00:03.3: [1039:7002] type 0 class 0x000c03
[    0.078685] pci 0000:00:03.3: reg 10: [mem 0xfe8fd000-0xfe8fdfff]
[    0.078766] pci 0000:00:03.3: PME# supported from D0 D3hot D3cold
[    0.078796] pci 0000:00:05.0: [1039:1183] type 0 class 0x000101
[    0.078816] pci 0000:00:05.0: reg 10: [io  0xcc00-0xcc07]
[    0.078828] pci 0000:00:05.0: reg 14: [io  0xc800-0xc803]
[    0.078840] pci 0000:00:05.0: reg 18: [io  0xc400-0xc407]
[    0.078851] pci 0000:00:05.0: reg 1c: [io  0xc000-0xc003]
[    0.078863] pci 0000:00:05.0: reg 20: [io  0xbc00-0xbc0f]
[    0.078875] pci 0000:00:05.0: reg 24: [io  0xb800-0xb87f]
[    0.078916] pci 0000:00:05.0: PME# supported from D3cold
[    0.078944] pci 0000:00:06.0: [1039:000a] type 1 class 0x000604
[    0.079041] pci 0000:00:06.0: PME# supported from D0 D3hot D3cold
[    0.079077] pci 0000:00:07.0: [1039:000a] type 1 class 0x000604
[    0.079172] pci 0000:00:07.0: PME# supported from D0 D3hot D3cold
[    0.079212] pci 0000:00:0f.0: [1039:7502] type 0 class 0x000403
[    0.079232] pci 0000:00:0f.0: reg 10: [mem 0xfe8f8000-0xfe8fbfff]
[    0.079315] pci 0000:00:0f.0: PME# supported from D0 D3hot D3cold
[    0.079362] pci 0000:00:1f.0: [1039:0004] type 1 class 0x000604
[    0.079464] pci 0000:00:1f.0: PME# supported from D0 D3hot D3cold
[    0.079507] pci 0000:01:00.0: [1039:6351] type 0 class 0x000300
[    0.079525] pci 0000:01:00.0: reg 10: [mem 0xd0000000-0xdfffffff pref]
[    0.079535] pci 0000:01:00.0: reg 14: [mem 0xfe9e0000-0xfe9fffff]
[    0.079545] pci 0000:01:00.0: reg 18: [io  0xdc00-0xdc7f]
[    0.079601] pci 0000:01:00.0: supports D1 D2
[    0.079641] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.079647] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.079652] pci 0000:00:01.0:   bridge window [mem 0xfe900000-0xfe9fffff]
[    0.079658] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff pref]
[    0.079743] pci 0000:02:00.0: [168c:002b] type 0 class 0x000280
[    0.079775] pci 0000:02:00.0: reg 10: [mem 0xfeaf0000-0xfeafffff 64bit]
[    0.079922] pci 0000:02:00.0: supports D1
[    0.079926] pci 0000:02:00.0: PME# supported from D0 D1 D3hot D3cold
[    0.084026] pci 0000:00:06.0: PCI bridge to [bus 02-02]
[    0.084038] pci 0000:00:06.0:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.084138] pci 0000:03:00.0: [10ec:8168] type 0 class 0x000200
[    0.084164] pci 0000:03:00.0: reg 10: [io  0xec00-0xecff]
[    0.084208] pci 0000:03:00.0: reg 18: [mem 0xfebff000-0xfebfffff 64bit]
[    0.084260] pci 0000:03:00.0: reg 30: [mem 0xfebc0000-0xfebdffff pref]
[    0.084373] pci 0000:03:00.0: supports D1 D2
[    0.084376] pci 0000:03:00.0: PME# supported from D1 D2 D3hot D3cold
[    0.084412] pci 0000:03:00.0: disabling ASPM on pre-1.1 PCIe device.  You can enable it with 'pcie_aspm=force'
[    0.084426] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    0.084434] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.084440] pci 0000:00:07.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.084503] pci 0000:00:1f.0: PCI bridge to [bus 04-04]
[    0.084541] pci_bus 0000:00: on NUMA node 0
[    0.084549] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.084865] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
[    0.084908] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[    0.085077]  pci0000:00: Requesting ACPI _OSC control (0x1d)
[    0.085421]  pci0000:00: ACPI _OSC control (0x19) granted
[    0.090731] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *10 11 12 14 15)
[    0.090814] ACPI: PCI Interrupt Link [LNKB] (IRQs 4 5 *7 10 11 12 14 15)
[    0.090892] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 7 10 11 12 14 15)
[    0.090966] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 *4 5 7 10 11 12 14 15)
[    0.091040] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 *11 12 14 15)
[    0.091113] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 7 10 11 12 14 15)
[    0.091188] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 12 14 *15)
[    0.091262] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
[    0.091414] vgaarb: device added: PCI:0000:01:00.0,decodes=io+mem,owns=io+mem,locks=none
[    0.091419] vgaarb: loaded
[    0.091421] vgaarb: bridge control possible 0000:01:00.0
[    0.091495] PCI: Using ACPI for IRQ routing
[    0.091501] PCI: pci_cache_line_size set to 64 bytes
[    0.091572] reserve RAM buffer: 000000000009fc00 - 000000000009ffff 
[    0.091575] reserve RAM buffer: 0000000077fb8000 - 0000000077ffffff 
[    0.091727] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.091734] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.091740] hpet0: 3 comparators, 32-bit 14.318180 MHz counter
[    0.096077] Switching to clocksource hpet
[    0.097836] pnp: PnP ACPI init
[    0.097864] ACPI: bus type pnp registered
[    0.098057] pnp 00:00: [bus 00-ff]
[    0.098062] pnp 00:00: [io  0x0cf8-0x0cff]
[    0.098065] pnp 00:00: [io  0x0000-0x0cf7 window]
[    0.098069] pnp 00:00: [io  0x0d00-0xffff window]
[    0.098072] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[    0.098076] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[    0.098079] pnp 00:00: [mem 0x78000000-0xdfffffff window]
[    0.098083] pnp 00:00: [mem 0xf0000000-0xfebfffff window]
[    0.098179] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[    0.098203] pnp 00:01: [dma 4]
[    0.098206] pnp 00:01: [io  0x0000-0x000f]
[    0.098209] pnp 00:01: [io  0x0081-0x0083]
[    0.098212] pnp 00:01: [io  0x0087]
[    0.098214] pnp 00:01: [io  0x0089-0x008b]
[    0.098217] pnp 00:01: [io  0x008f]
[    0.098220] pnp 00:01: [io  0x00c0-0x00df]
[    0.098257] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[    0.098307] pnp 00:02: [io  0x0060]
[    0.098310] pnp 00:02: [io  0x0064]
[    0.098327] pnp 00:02: [irq 1]
[    0.098368] pnp 00:02: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[    0.098439] pnp 00:03: [irq 12]
[    0.098487] pnp 00:03: Plug and Play ACPI device, IDs ETD0001 SYN0a00 SYN0002 PNP0f03 PNP0f13 PNP0f12 (active)
[    0.098501] pnp 00:04: [io  0x0061]
[    0.098539] pnp 00:04: Plug and Play ACPI device, IDs PNP0800 (active)
[    0.098552] pnp 00:05: [io  0x00f0-0x00ff]
[    0.098559] pnp 00:05: [irq 13]
[    0.098597] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[    0.098764] pnp 00:06: [io  0x0010-0x001f]
[    0.098768] pnp 00:06: [io  0x0022-0x003f]
[    0.098771] pnp 00:06: [io  0x0044-0x005f]
[    0.098773] pnp 00:06: [io  0x0062-0x0063]
[    0.098776] pnp 00:06: [io  0x0065-0x006f]
[    0.098779] pnp 00:06: [io  0x0072-0x007f]
[    0.098782] pnp 00:06: [io  0x0080]
[    0.098784] pnp 00:06: [io  0x0084-0x0086]
[    0.098787] pnp 00:06: [io  0x0088]
[    0.098790] pnp 00:06: [io  0x008c-0x008e]
[    0.098793] pnp 00:06: [io  0x0090-0x009f]
[    0.098796] pnp 00:06: [io  0x00a2-0x00bf]
[    0.098800] pnp 00:06: [io  0x00e0-0x00ef]
[    0.098803] pnp 00:06: [io  0x0290-0x0297]
[    0.098806] pnp 00:06: [io  0x0c00-0x0c05]
[    0.098809] pnp 00:06: [io  0x0d00-0x0d05]
[    0.098812] pnp 00:06: [io  0x0480-0x048f]
[    0.098814] pnp 00:06: [io  0x04d0-0x04d1]
[    0.098817] pnp 00:06: [io  0x0800-0x087f]
[    0.098820] pnp 00:06: [io  0x0880-0x08ff]
[    0.098823] pnp 00:06: [io  0x0c00-0x0c7f]
[    0.098826] pnp 00:06: [io  0x0000-0xffffffff disabled]
[    0.098829] pnp 00:06: [io  0x2000-0x20fe]
[    0.098833] pnp 00:06: [mem 0xfff80000-0xffffffff]
[    0.098836] pnp 00:06: [mem 0xffb80000-0xffbfffff]
[    0.098839] pnp 00:06: [mem 0xffee0000-0xffefffff]
[    0.098842] pnp 00:06: [mem 0xfed10000-0xfed3ffff]
[    0.098940] system 00:06: [io  0x0290-0x0297] has been reserved
[    0.098945] system 00:06: [io  0x0c00-0x0c05] has been reserved
[    0.098949] system 00:06: [io  0x0d00-0x0d05] has been reserved
[    0.098953] system 00:06: [io  0x0480-0x048f] has been reserved
[    0.098957] system 00:06: [io  0x04d0-0x04d1] has been reserved
[    0.098961] system 00:06: [io  0x0800-0x087f] has been reserved
[    0.098965] system 00:06: [io  0x0880-0x08ff] has been reserved
[    0.098970] system 00:06: [io  0x0c00-0x0c7f] could not be reserved
[    0.098974] system 00:06: [io  0x2000-0x20fe] has been reserved
[    0.098979] system 00:06: [mem 0xfff80000-0xffffffff] has been reserved
[    0.098983] system 00:06: [mem 0xffb80000-0xffbfffff] has been reserved
[    0.098988] system 00:06: [mem 0xffee0000-0xffefffff] has been reserved
[    0.098992] system 00:06: [mem 0xfed10000-0xfed3ffff] has been reserved
[    0.098997] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.099076] pnp 00:07: [irq 0 disabled]
[    0.099084] pnp 00:07: [irq 8]
[    0.099088] pnp 00:07: [mem 0xfed00000-0xfed003ff]
[    0.099130] pnp 00:07: Plug and Play ACPI device, IDs PNP0103 (active)
[    0.099179] pnp 00:08: [io  0x0070-0x0071]
[    0.099223] pnp 00:08: Plug and Play ACPI device, IDs PNP0b00 (active)
[    0.099297] pnp 00:09: [io  0x0250-0x0253]
[    0.099301] pnp 00:09: [io  0x0256-0x025f]
[    0.099304] pnp 00:09: [mem 0xfec00000-0xfec00fff]
[    0.099307] pnp 00:09: [mem 0xfee00000-0xfee00fff]
[    0.099372] system 00:09: [io  0x0250-0x0253] has been reserved
[    0.099376] system 00:09: [io  0x0256-0x025f] has been reserved
[    0.099381] system 00:09: [mem 0xfec00000-0xfec00fff] could not be reserved
[    0.099385] system 00:09: [mem 0xfee00000-0xfee00fff] has been reserved
[    0.099390] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.099459] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[    0.099524] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[    0.099530] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[    0.099821] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[    0.099825] pnp 00:0b: [mem 0x000c0000-0x000cffff]
[    0.099828] pnp 00:0b: [mem 0x000e0000-0x000fffff]
[    0.099831] pnp 00:0b: [mem 0x00100000-0x77ffffff]
[    0.099834] pnp 00:0b: [mem 0xe0000000-0xffffffff]
[    0.099922] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[    0.099927] system 00:0b: [mem 0x000c0000-0x000cffff] could not be reserved
[    0.099931] system 00:0b: [mem 0x000e0000-0x000fffff] could not be reserved
[    0.099936] system 00:0b: [mem 0x00100000-0x77ffffff] could not be reserved
[    0.099940] system 00:0b: [mem 0xe0000000-0xffffffff] could not be reserved
[    0.099945] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[    0.100124] pnp: PnP ACPI: found 12 devices
[    0.100127] ACPI: ACPI bus type pnp unregistered
[    0.100133] PnPBIOS: Disabled by ACPI PNP
[    0.137430] PCI: max bus depth: 1 pci_try_num: 2
[    0.137474] pci 0000:00:01.0: PCI bridge to [bus 01-01]
[    0.137479] pci 0000:00:01.0:   bridge window [io  0xd000-0xdfff]
[    0.137487] pci 0000:00:01.0:   bridge window [mem 0xfe900000-0xfe9fffff]
[    0.137493] pci 0000:00:01.0:   bridge window [mem 0xd0000000-0xdfffffff pref]
[    0.137501] pci 0000:00:06.0: PCI bridge to [bus 02-02]
[    0.137508] pci 0000:00:06.0:   bridge window [mem 0xfea00000-0xfeafffff]
[    0.137519] pci 0000:00:07.0: PCI bridge to [bus 03-03]
[    0.137524] pci 0000:00:07.0:   bridge window [io  0xe000-0xefff]
[    0.137531] pci 0000:00:07.0:   bridge window [mem 0xfeb00000-0xfebfffff]
[    0.137541] pci 0000:00:1f.0: PCI bridge to [bus 04-04]
[    0.137567] pci 0000:00:01.0: setting latency timer to 64
[    0.137578] pci 0000:00:06.0: setting latency timer to 64
[    0.137588] pci 0000:00:07.0: setting latency timer to 64
[    0.137598] pci 0000:00:1f.0: setting latency timer to 64
[    0.137604] pci_bus 0000:00: resource 4 [io  0x0000-0x0cf7]
[    0.137607] pci_bus 0000:00: resource 5 [io  0x0d00-0xffff]
[    0.137611] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[    0.137614] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[    0.137618] pci_bus 0000:00: resource 8 [mem 0x78000000-0xdfffffff]
[    0.137621] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
[    0.137625] pci_bus 0000:01: resource 0 [io  0xd000-0xdfff]
[    0.137628] pci_bus 0000:01: resource 1 [mem 0xfe900000-0xfe9fffff]
[    0.137632] pci_bus 0000:01: resource 2 [mem 0xd0000000-0xdfffffff pref]
[    0.137636] pci_bus 0000:02: resource 1 [mem 0xfea00000-0xfeafffff]
[    0.137639] pci_bus 0000:03: resource 0 [io  0xe000-0xefff]
[    0.137643] pci_bus 0000:03: resource 1 [mem 0xfeb00000-0xfebfffff]
[    0.137698] NET: Registered protocol family 2
[    0.137768] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.138042] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.138976] TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
[    0.139261] TCP: Hash tables configured (established 131072 bind 65536)
[    0.139265] TCP reno registered
[    0.139270] UDP hash table entries: 512 (order: 1, 8192 bytes)
[    0.139283] UDP-Lite hash table entries: 512 (order: 1, 8192 bytes)
[    0.139445] NET: Registered protocol family 1
[    0.332065] pci 0000:01:00.0: Boot video device
[    0.332077] PCI: CLS 32 bytes, default 64
[    0.332166] Unpacking initramfs...
[    0.727773] Freeing initrd memory: 10096k freed
[    0.734306] Simple Boot Flag at 0x71 set to 0x1
[    0.735123] audit: initializing netlink socket (disabled)
[    0.735141] type=2000 audit(1365363390.728:1): initialized
[    0.757486] highmem bounce pool size: 64 pages
[    0.757493] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.757623] VFS: Disk quotas dquot_6.5.2
[    0.757647] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.757722] msgmni has been set to 1733
[    0.757921] alg: No test for stdrng (krng)
[    0.757958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[    0.757963] io scheduler noop registered
[    0.757965] io scheduler deadline registered
[    0.757975] io scheduler cfq registered (default)
[    0.758273] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.758303] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.758306] acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
[    0.758740] ERST: Table is not found!
[    0.758742] GHES: HEST is not enabled!
[    0.758761] isapnp: Scanning for PnP cards...
[    1.112368] isapnp: No Plug & Play device found
[    1.112467] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[    1.113206] Linux agpgart interface v0.103
[    1.113332] agpgart-sis 0000:00:00.0: SiS chipset [1039/0671]
[    1.121316] agpgart-sis 0000:00:00.0: AGP aperture is 128M @ 0xf0000000
[    1.121495] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    1.124958] i8042: Detected active multiplexing controller, rev 1.1
[    1.126156] serio: i8042 KBD port at 0x60,0x64 irq 1
[    1.126168] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[    1.126212] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[    1.126251] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[    1.126286] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[    1.126450] mousedev: PS/2 mouse device common for all mice
[    1.126529] rtc_cmos 00:08: RTC can wake from S4
[    1.126659] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0
[    1.126685] rtc0: alarms up to one year, 114 bytes nvram, hpet irqs
[    1.126759] EISA: Probing bus 0 at eisa.0
[    1.126763] EISA: Cannot allocate resource for mainboard
[    1.126766] Cannot allocate resource for EISA slot 1
[    1.126769] Cannot allocate resource for EISA slot 2
[    1.126772] Cannot allocate resource for EISA slot 3
[    1.126774] Cannot allocate resource for EISA slot 4
[    1.126777] Cannot allocate resource for EISA slot 5
[    1.126780] Cannot allocate resource for EISA slot 6
[    1.126782] Cannot allocate resource for EISA slot 7
[    1.126785] Cannot allocate resource for EISA slot 8
[    1.126787] EISA: Detected 0 cards.
[    1.126791] cpuidle: using governor ladder
[    1.126794] cpuidle: using governor menu
[    1.127041] TCP cubic registered
[    1.127068] NET: Registered protocol family 10
[    1.127628] Mobile IPv6
[    1.127633] NET: Registered protocol family 17
[    1.127640] Registering the dns_resolver key type
[    1.127658] Using IPI Shortcut mode
[    1.127821] PM: Hibernation image not present or could not be loaded.
[    1.127837] registered taskstats version 1
[    1.128214] rtc_cmos 00:08: setting system clock to 2013-04-07 19:36:31 UTC (1365363391)
[    1.128258] Initializing network drop monitor service
[    1.128400] Freeing unused kernel memory: 452k freed
[    1.128612] Write protecting the kernel text: 2592k
[    1.128632] Write protecting the kernel read-only data: 1040k
[    1.149953] udevd[42]: starting version 175
[    1.163044] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input0
[    1.231966] SCSI subsystem initialized
[    1.262557] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    1.262632] r8169 0000:03:00.0: setting latency timer to 64
[    1.262719] r8169 0000:03:00.0: irq 40 for MSI/MSI-X
[    1.263314] r8169 0000:03:00.0: eth0: RTL8168b/8111b at 0xf801a000, 48:5b:39:37:0a:36, XID 18000000 IRQ 40
[    1.263319] r8169 0000:03:00.0: eth0: jumbo features [frames: 4080 bytes, tx checksumming: ko]
[    1.274355] usbcore: registered new interface driver usbfs
[    1.274396] usbcore: registered new interface driver hub
[    1.281402] usbcore: registered new device driver usb
[    1.282042] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.282109] ehci_hcd 0000:00:03.3: EHCI Host Controller
[    1.282144] ehci_hcd 0000:00:03.3: new USB bus registered, assigned bus number 1
[    1.282198] ehci_hcd 0000:00:03.3: irq 22, io mem 0xfe8fd000
[    1.297604] ehci_hcd 0000:00:03.3: USB 2.0 started, EHCI 1.00
[    1.297669] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    1.297674] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.297677] usb usb1: Product: EHCI Host Controller
[    1.297680] usb usb1: Manufacturer: Linux 3.2.0-4-486 ehci_hcd
[    1.297683] usb usb1: SerialNumber: 0000:00:03.3
[    1.297870] hub 1-0:1.0: USB hub found
[    1.297878] hub 1-0:1.0: 8 ports detected
[    1.298442] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.298505] ohci_hcd 0000:00:03.0: OHCI Host Controller
[    1.298524] ohci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
[    1.298554] ohci_hcd 0000:00:03.0: irq 20, io mem 0xfe8ff000
[    1.320072] libata version 3.00 loaded.
[    1.333523] thermal LNXTHERM:00: registered as thermal_zone0
[    1.333528] ACPI: Thermal Zone [THRM] (56 C)
[    1.354073] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    1.354078] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.354082] usb usb2: Product: OHCI Host Controller
[    1.354085] usb usb2: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[    1.354088] usb usb2: SerialNumber: 0000:00:03.0
[    1.354291] hub 2-0:1.0: USB hub found
[    1.354299] hub 2-0:1.0: 4 ports detected
[    1.354396] pata_sis 0000:00:02.5: version 0.5.2
[    1.360247] scsi0 : pata_sis
[    1.364668] scsi1 : pata_sis
[    1.365292] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xfff0 irq 14
[    1.365297] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xfff8 irq 15
[    1.365551] sata_sis 0000:00:05.0: version 1.0
[    1.365586] sata_sis 0000:00:05.0: Detected SiS 1183/966/966L/968/680 controller in PATA mode
[    1.370673] scsi2 : sata_sis
[    1.377283] scsi3 : sata_sis
[    1.377932] ata3: PATA max UDMA/133 cmd 0xcc00 ctl 0xc800 bmdma 0xbc00 irq 17
[    1.377937] ata4: PATA max UDMA/133 cmd 0xc400 ctl 0xc000 bmdma 0xbc08 irq 17
[    1.378040] ohci_hcd 0000:00:03.1: OHCI Host Controller
[    1.378062] ohci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
[    1.378093] ohci_hcd 0000:00:03.1: irq 21, io mem 0xfe8fe000
[    1.434061] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[    1.434067] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.434071] usb usb3: Product: OHCI Host Controller
[    1.434074] usb usb3: Manufacturer: Linux 3.2.0-4-486 ohci_hcd
[    1.434077] usb usb3: SerialNumber: 0000:00:03.1
[    1.434273] hub 3-0:1.0: USB hub found
[    1.434282] hub 3-0:1.0: 4 ports detected
[    1.524135] ata2: port disabled--ignoring
[    1.540605] ata3.00: ATA-8: ST9250315AS, 0002SDM1, max UDMA/133
[    1.540610] ata3.00: 488397168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.556585] ata3.00: configured for UDMA/133
[    1.556737] scsi 2:0:0:0: Direct-Access     ATA      ST9250315AS      0002 PQ: 0 ANSI: 5
[    1.664020] usb 1-2: new high-speed USB device number 3 using ehci_hcd
[    1.732013] Refined TSC clocksource calibration: 1500.340 MHz.
[    1.732019] Switching to clocksource tsc
[    1.736562] ata4.00: ATAPI: TSSTcorp CDDVDW TS-L633C, AS01, max UDMA/100
[    1.768212] ata4.00: configured for UDMA/100
[    1.773468] scsi 3:0:0:0: CD-ROM            TSSTcorp CDDVDW TS-L633C  AS01 PQ: 0 ANSI: 5
[    1.794157] sd 2:0:0:0: [sda] 488397168 512-byte logical blocks: (250 GB/232 GiB)
[    1.794229] sd 2:0:0:0: [sda] Write Protect is off
[    1.794233] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    1.794262] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    1.799609] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[    1.799615] cdrom: Uniform CD-ROM driver Revision: 3.20
[    1.800310] sr 3:0:0:0: Attached scsi CD-ROM sr0
[    1.822236] usb 1-2: New USB device found, idVendor=8564, idProduct=1000
[    1.822242] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    1.822245] usb 1-2: Product: Flash Disk
[    1.822248] usb 1-2: Manufacturer: USB
[    1.822250] usb 1-2: SerialNumber: FBF1008180000151
[    1.826963] Initializing USB Mass Storage driver...
[    1.827091] scsi4 : usb-storage 1-2:1.0
[    1.827213] usbcore: registered new interface driver usb-storage
[    1.827216] USB Mass Storage support registered.
[    1.872703]  sda: sda1 sda2 sda3 < sda5 sda6 sda7 sda8 > sda4
[    1.873787] sd 2:0:0:0: [sda] Attached SCSI disk
[    1.883658] sd 2:0:0:0: Attached scsi generic sg0 type 0
[    1.883816] sr 3:0:0:0: Attached scsi generic sg1 type 5
[    1.932026] usb 1-5: new high-speed USB device number 4 using ehci_hcd
[    2.098373] usb 1-5: New USB device found, idVendor=13d3, idProduct=5130
[    2.098378] usb 1-5: New USB device strings: Mfr=2, Product=1, SerialNumber=0
[    2.098382] usb 1-5: Product: USB 2.0 Camera
[    2.098385] usb 1-5: Manufacturer: Sonix Technology Co., Ltd.
[    2.212033] usb 1-7: new high-speed USB device number 5 using ehci_hcd
[    2.345380] usb 1-7: New USB device found, idVendor=058f, idProduct=6366
[    2.345386] usb 1-7: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[    2.345389] usb 1-7: Product: Mass Storage Device
[    2.345392] usb 1-7: Manufacturer: Generic
[    2.345394] usb 1-7: SerialNumber: 058F63666433
[    2.346300] scsi5 : usb-storage 1-7:1.0
[    2.648026] usb 2-1: new low-speed USB device number 2 using ohci_hcd
[    2.857120] usb 2-1: New USB device found, idVendor=2166, idProduct=6649
[    2.857125] usb 2-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.857129] usb 2-1: Product:  USB OPTICAL MOUSE
[    2.872559] input:  USB OPTICAL MOUSE as /devices/pci0000:00/0000:00:03.0/usb2/2-1/2-1:1.0/input/input1
[    2.873072] generic-usb 0003:2166:6649.0001: input,hidraw0: USB HID v1.11 Mouse [ USB OPTICAL MOUSE] on usb-0000:00:03.0-1/input0
[    2.873406] usbcore: registered new interface driver usbhid
[    2.873411] usbhid: USB HID core driver
[    2.971919] scsi: waiting for bus probes to complete ...
[    3.086575] scsi 4:0:0:0: Direct-Access     USB      Flash CD         1100 PQ: 0 ANSI: 0 CCS
[    3.088194] sd 4:0:0:0: Attached scsi generic sg2 type 0
[    3.088492] sd 4:0:0:0: [sdb] 7833600 512-byte logical blocks: (4.01 GB/3.73 GiB)
[    3.089195] sd 4:0:0:0: [sdb] Write Protect is off
[    3.089201] sd 4:0:0:0: [sdb] Mode Sense: 43 00 00 00
[    3.089941] sd 4:0:0:0: [sdb] No Caching mode page present
[    3.089985] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.094176] sd 4:0:0:0: [sdb] No Caching mode page present
[    3.094221] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.095330]  sdb: sdb1
[    3.098673] sd 4:0:0:0: [sdb] No Caching mode page present
[    3.098717] sd 4:0:0:0: [sdb] Assuming drive cache: write through
[    3.098756] sd 4:0:0:0: [sdb] Attached SCSI disk
[    3.336416] microcode: CPU0 sig=0x10661, pf=0x4, revision=0x0
[    3.342393] platform microcode: firmware: agent loaded intel-ucode/06-16-01 into memory
[    3.342702] microcode: CPU0 updated to revision 0x36, date = 2007-05-01
[    3.343346] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[    3.443212] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[    3.473209] scsi 5:0:0:0: Direct-Access     Multiple Card  Reader     1.00 PQ: 0 ANSI: 0
[    3.473809] sd 5:0:0:0: Attached scsi generic sg3 type 0
[    4.166329] sd 5:0:0:0: [sdc] 1989632 512-byte logical blocks: (1.01 GB/971 MiB)
[    4.167848] sd 5:0:0:0: [sdc] Write Protect is off
[    4.167854] sd 5:0:0:0: [sdc] Mode Sense: 03 00 00 00
[    4.168584] sd 5:0:0:0: [sdc] No Caching mode page present
[    4.168628] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[    4.171819] sd 5:0:0:0: [sdc] No Caching mode page present
[    4.171859] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[    4.173362]  sdc: sdc1
[    4.175947] sd 5:0:0:0: [sdc] No Caching mode page present
[    4.175988] sd 5:0:0:0: [sdc] Assuming drive cache: write through
[    4.176038] sd 5:0:0:0: [sdc] Attached SCSI removable disk
[    5.140513] udevd[339]: starting version 175
[    5.638351] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input2
[    5.638361] ACPI: Power Button [PWRB]
[    5.638439] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input3
[    5.638445] ACPI: Sleep Button [SLPB]
[    5.638522] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input4
[    5.639503] Monitor-Mwait will be used to enter C-1 state
[    5.644232] ACPI: Lid Switch [LID]
[    5.644344] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input5
[    5.644352] ACPI: Power Button [PWRF]
[    5.648479] ACPI: AC Adapter [AC0] (on-line)
[    5.736919] acpi device:29: registered as cooling_device1
[    5.737050] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A03:00/device:27/LNXVIDEO:00/input/input6
[    5.737061] ACPI: Video Device [VGA] (multi-head: yes  rom: no  post: no)
[    5.752169] ACPI: Battery Slot [BAT0] (battery present)
[    5.810486] input: PC Speaker as /devices/platform/pcspkr/input/input7
[    5.929876] coretemp coretemp.0: Using relative temperature scale!
[    6.064659] psmouse serio4: hgpk: ID: 10 00 64
[    6.136852] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[    6.149023] psmouse serio4: elantech: assuming hardware version 2 (with firmware version 0x040101)
[    6.181737] psmouse serio4: elantech: Synaptics capabilities query result 0x7e, 0x13, 0x0d.
[    6.193106] asus_laptop: Asus Laptop Support version 0.42
[    6.193417] asus_laptop:   K50C model detected
[    6.193699] asus_laptop: Backlight controlled by ACPI video driver
[    6.193786] input: Asus Laptop extra buttons as /devices/platform/asus_laptop/input/input8
[    6.200278] cfg80211: Calling CRDA to update world regulatory domain
[    6.313333] input: ETPS/2 Elantech Touchpad as /devices/platform/i8042/serio4/input/input9
[    6.453585] ath9k 0000:02:00.0: setting latency timer to 64
[    6.502584] ath: EEPROM regdomain: 0x8283
[    6.502587] ath: EEPROM indicates we should expect a country code
[    6.502591] ath: doing EEPROM country->regdmn map search
[    6.502593] ath: country maps to regdmn code: 0x3
[    6.502596] ath: Country alpha2 being used: RU
[    6.502598] ath: Regpair used: 0x3
[    6.543964] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[    6.544744] Registered led device: ath9k-phy0
[    6.544753] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xf82e0000, irq=18
[    7.031985] snd_hda_intel 0000:00:0f.0: setting latency timer to 64
[    7.086397] cfg80211: World regulatory domain updated:
[    7.086403] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.086408] cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.086412] cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.086416] cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[    7.086420] cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.086424] cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[    7.086657] cfg80211: Calling CRDA for country: RU
[    7.101483] cfg80211: Regulatory domain changed to country: RU
[    7.101489] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[    7.101493] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[    7.101497] cfg80211:     (5735000 KHz - 5835000 KHz @ 20000 KHz), (N/A, 3000 mBm)
[    7.208041] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:0f.0/input/input10
[    7.212308] input: HDA SIS966 Mic as /devices/pci0000:00/0000:00:0f.0/sound/card0/input11
[    7.212582] input: HDA SIS966 Headphone as /devices/pci0000:00/0000:00:0f.0/sound/card0/input12
[    7.428802] Linux media interface: v0.10
[    7.443321] Linux video capture interface: v2.00
[    7.546172] uvcvideo: Found UVC 1.00 device USB 2.0 Camera (13d3:5130)
[    7.554036] input: USB 2.0 Camera as /devices/pci0000:00/0000:00:03.3/usb1/1-5/1-5:1.0/input/input13
[    7.554610] usbcore: registered new interface driver uvcvideo
[    7.554614] USB Video Class driver (1.1.1)
[   10.045813] EXT4-fs (sda6): re-mounted. Opts: (null)
[   10.214276] EXT4-fs (sda6): re-mounted. Opts: errors=remount-ro
[   10.314645] loop: module loaded
[   15.289623] Bluetooth: Core ver 2.16
[   15.289661] NET: Registered protocol family 31
[   15.289664] Bluetooth: HCI device and connection manager initialized
[   15.289669] Bluetooth: HCI socket layer initialized
[   15.289672] Bluetooth: L2CAP socket layer initialized
[   15.290045] Bluetooth: SCO socket layer initialized
[   15.309626] Bluetooth: RFCOMM TTY layer initialized
[   15.309634] Bluetooth: RFCOMM socket layer initialized
[   15.309637] Bluetooth: RFCOMM ver 1.11
[   15.332166] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.332171] Bluetooth: BNEP filters: protocol multicast
[   17.480359] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[   17.500203] r8169 0000:03:00.0: eth0: link down
[   17.500459] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   19.391672] wlan0: authenticate with fc:75:16:e9:00:38 (try 1)
[   19.393828] wlan0: authenticated
[   19.394453] wlan0: associate with fc:75:16:e9:00:38 (try 1)
[   19.398215] wlan0: RX AssocResp from fc:75:16:e9:00:38 (capab=0x401 status=0 aid=1)
[   19.398222] wlan0: associated
[   19.405924] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[   19.407724] cfg80211: Calling CRDA for country: RU
[   19.421908] cfg80211: Regulatory domain changed to country: RU
[   19.421914] cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[   19.421919] cfg80211:     (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[   19.421922] cfg80211:     (5735000 KHz - 5835000 KHz @ 20000 KHz), (N/A, 3000 mBm)
[   27.348087] fuse init (API version 7.17)
[   29.824024] wlan0: no IPv6 routers present

5 (19.04.2013 00:34 отредактировано khan77)

Re: Настройка TouchPad в Debian

Команды

 synclient TouchpadOff=1

и

synclient TouchpadOff=0

работают "искаропки", ничего устанавливать не пришлось smile Это уже здорово! Теперь вот, немного поднабравшись опыта в кранче думаю, что и хоткеи можно навесить без установки дополнительных пакетов- через правку rc.xml, правда ведь? Я, правда, с ситнаксисом пока не совсем там освоился, так что, если подскажете правильные команды, то буду благодарен...